- 11 degrees of freedom on six motors The thumb gets driven flexion and abduction, each finger a driven flexion joint coupled to a passive one, and every position repeats to 0.1°.
- 20 kg from a 383 g hand A five-finger grip of at least 50 N and a 15 N pinch let the 383 g right hand carry at least 20 kg.
- One connector, two protocols The DIP switch under the wrist cover sets Modbus-RTU over RS-485 or CAN FD, and either one reaches 500 Hz.
- Light on power The Basic takes 12–28 V and draws 65 mA at rest and 4.6 A at peak at 24 V, the lowest figures in the Revo 2 range.
- Built-in protection Current, stall, over-temperature and collision protection guard the motors, and a light on the back of the hand shows power-up, low voltage, OTA and fault states.
- Open SDK and simulation models Python and C/C++ SDKs for Linux, Windows and ROS come with URDF and MuJoCo models of the hand.
Description
The BrainCo Revo 2 Basic Right (XRR) is the right-hand bionic dexterous robotic hand that starts BrainCo's Revo 2 range. It weighs 383 g, which BrainCo compares to a bottle of water, measures 160 mm from palm base to middle fingertip, and moves five fingers through 11 degrees of freedom with six coreless motors.
Choose the Basic when the controller already speaks RS-485 or CAN and the work is grasping rather than sensing: pick-and-place, teleoperation, demonstration robots and manipulation courses. A DIP switch under the wrist cover sets Modbus-RTU over RS-485 or CAN FD, each at up to 500 Hz; the supply is 12–28 V, and at 24 V the hand draws 65 mA at rest and 350 mA on average while flexing without load. Position, velocity, current, cascaded and compliance control are all built in, and a turbo mode re-grips soft or shifting objects every 500 ms after a stall.
The fingers close with at least 50 N, pinch with 15 N and hold at least 20 kg, open 100 mm between thumb and index finger, and complete a flex or extension in 0.65 s or less. Moving up the range keeps that hardware: the Revo 2 Pro right hand (XER) adds EtherCAT at up to 1 kHz and a 12–64 V input, and the Revo 2 Touch right hand (XTR) also senses with all five fingertips.
Out of the box the XRR answers to device ID 127, while the Revo 2 Basic left hand (XRL) answers to 126, so both hands of a humanoid run on one bus. Each comes with an RS-485/CAN FD cable, and BrainCo's Python and C/C++ SDKs, URDF and MuJoCo models and over-the-air firmware updates support it on Linux, Windows and ROS. Compare it with the rest of our dexterous robotic hands.
Key Capabilities
- 11 degrees of freedom on six motors: The thumb gets driven flexion and abduction, each finger a driven flexion joint coupled to a passive one, and every position repeats to 0.1°.
- 20 kg from a 383 g hand: A five-finger grip of at least 50 N and a 15 N pinch let the 383 g right hand carry at least 20 kg.
- One connector, two protocols: The DIP switch under the wrist cover sets Modbus-RTU over RS-485 or CAN FD, and either one reaches 500 Hz.
- Light on power: The Basic takes 12–28 V and draws 65 mA at rest and 4.6 A at peak at 24 V, the lowest figures in the Revo 2 range.
- Built-in protection: Current, stall, over-temperature and collision protection guard the motors, and a light on the back of the hand shows power-up, low voltage, OTA and fault states.
- Open SDK and simulation models: Python and C/C++ SDKs for Linux, Windows and ROS come with URDF and MuJoCo models of the hand.
Buying through Robotix Market
This unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.
Features
Specs
| Brand | BrainCo |
|---|---|
| Model | Revo 2 Basic |
| Version code | XRR (right hand); the left hand is XRL |
| Hand side | Right |
| Fingers | 5 |
| Degrees of freedom | 11 (6 active, 5 passive) |
| Motors | 6 coreless motors, magnetic encoders, one integrated controller |
| Active joints | Thumb flexion, thumb abduction/adduction, and flexion of the index, middle, ring and little fingers |
| Range of motion | Thumb flexion 0–59°, thumb abduction/adduction 0–90°, each finger 0–81° |
| Weight | 383 g (without wrist) |
| Hand length (palm base to middle fingertip) | 160 mm |
| Maximum palm width | 78.5 mm |
| Thumb length | 92 mm |
| Wrist | 38 mm diameter, 13.5 mm high |
| Maximum opening (thumb to index finger) | 100 mm |
| Five-finger grip force | ≥ 50 N |
| Pinch force | ≥ 15 N |
| Maximum payload | ≥ 20 kg |
| Repeat control precision | 0.1° |
| Flexion/extension time | ≤ 0.65 s |
| Operating noise | ≤ 50 dB at 50 cm |
| Tactile sensing | None (fitted on the Revo 2 Touch) |
| Communication interfaces | RS-485 (Modbus-RTU) or CAN FD, selected with a DIP switch under the wrist cover |
| Communication frequency | Up to 500 Hz |
| Interface connector | BM05B-PASS-TFT, under the wrist |
| Supply voltage | 12–28 V |
| Current at 24 V | 65 mA static, 350 mA average with no load, 4.6 A maximum |
| Control modes | Position, velocity and current control; cascaded and compliance control |
| Wrist mounting | 4 × M3 screws (Basic wrist flange) |
| Default device ID | 127 (the left hand uses 126), adjustable 1–254 |
| Protection | Current, stall, over-temperature and collision protection |
| SDK | Python and C/C++ for Linux, Windows and ROS |
| Simulation models | URDF (ROS 1 and ROS 2) and MuJoCo |
| Firmware updates | Over the air (OTA) |
| Materials | Aerospace-grade aluminium alloy and food-grade plastic |
| Operating environment | −10 to 40 °C, up to 90 % relative humidity |
| Standard colours | Space Gray, Silver |
| What's in the box | Hand and one RS-485/CAN FD communication cable |
| Robot mounting | Confirm at quote |
Industries
Frequently Asked Questions
The BrainCo Revo 2 Basic Bionic Hand Right (XRR) is priced at €3.120 in your market.
All three share the 383 g, 11-degree-of-freedom hand with at least 50 N grip and a 20 kg payload. The Basic runs RS-485 or CAN FD on 12–28 V, the Pro adds EtherCAT and a 12–64 V input, and the Touch adds fingertip tactile sensors to the Pro.
Six motors drive six joints: thumb flexion (0–59°), thumb abduction/adduction (0–90°) and flexion of each finger (0–81°). Five passive joints follow, for 11 degrees of freedom in total.
At least 50 N across five fingers, 15 N in a pinch and a 20 kg payload, from a hand that weighs 383 g.
RS-485 with Modbus-RTU or CAN FD, chosen by a DIP switch, at up to 500 Hz on 12–28 V. BrainCo's Python and C/C++ SDKs run on Linux, Windows and ROS; mounting to your robot is confirmed with the quotation.
The XRR is the right hand. The matching Revo 2 Basic left hand is the XRL; with default IDs 127 and 126 the two are addressed separately on one bus.
Recently Viewed
You haven't viewed any products yet.
